Commonly, when you are at the peak moment while seriously carving and all of a sudden, you hear a squeaky noise. Yes, it’s quite annoying to notice that, right? Worry no more; in this article you’ll know the reasons or answers to your question.
In different occurrences, there are components of your skateboard that might cause your squeaky problems, such as bearings, riser pads, and axles. Because excessive pressure, when applied, might cause friction that results in the annoying sounds it creates. So, if you try to find the problem and still can’t figure it out, read on here and don’t skip.
Table of Contents
The Reason My Skateboard Squeak When I Turn?
There are a lot of reasons why your skateboard squeaks a lot. Here listed below are the possible reasons why it’s creating unnecessary noises, but as we go along, we’ll discuss them with further explanation.
- Loose Bolts and Nuts
- Bearings
- Uneven Washers
- Broken Riser Pad
- Worn out wheels
- Unlubricated Parts
- Axle and Squeaky Trucks
There are ways to get rid of those grating noises on each of your skateboard parts through good maintenance. The extra benefit of routine maintenance is to spin it freely, especially your while, and to reduce friction in terms of excessive pressure that it takes when you’re riding it that commonly results in squeaky skateboard trucks.
Possible Reasons for Squeaking Noise on Your Skateboard
Squeaking noises may have a variety of causes, most of which are obvious. In this part, we’ll go into further depth about each reason. A proper way of care and maintenance on your skateboard, in the long run, may save you a lot of money.
Listed below are the possible reasons why your skateboard creates squeaking noise:
1. Bearings
The solution here is very straightforward. Bearings are the ones that get rolling and are affected by friction. We know that it will not last forever, so you should look after it so you won’t get a squeaky bushings skateboard.
- It is advisable to remove all the bearings by popping them out.
- Spinning the bearings freely will quickly tell you if it needs to be replaced or lubricated.
- When it comes to bearing lubricants, silicone-based lubricants are ideal.
- Also, if the bearing balls are not complete, you may opt to consider replacing them.
2. Skateboard Truck’s Bushing
Most of the time, trucks squeak because of their bushings, which are the most prevalent culprit. Bushings serve as stabilization to your skateboard truck, as it prevents direct contact and friction. Take a look at your bushings and examine if it shows signs of wear or tear.
It may deteriorate due to harsh conditions, temperature, and weather in the long run.
- If your squeaky bushings show signs of tear and are pretty uneven in shape, it’s time to replace them.
- If you don’t have the budget, try altering them or interchange their places once in a while. It also fixes the problem of squeaky bushings skateboard.
3. Riser Pads
Many individuals are unaware of this part. The riser pads are the one that separates the board from the truck. These parts are for reducing vibrations and preventing fractures.
They don’t function well if there are cuts and rips. The skateboard will be damaged if you don’t inspect the riser pads regularly. Therefore, ensure that the screw is tightened correctly to avoid vibrations and noises.
4. Wheels
If your bearings are working fine, you must inspect your wheels. Sometimes, the wheel decreases its diameter due to excessive use, and it may have dents or flat spots that cause a bumpy feeling when skating. Also, it may apply uneven force on the bearings, axles, and trucks that may cause squeaky noises.
5. Pivot Cups and Screws
If you hear new skateboard trucks squeak, check for any loose screws or pivot cups. It’s an easy repair.
- You can reduce the noise by tightening all the screws.
- Other than that, you may check out the pivot cup. The pivot cup and hanger may have minor gaps. Rotate the rubber cup to hear the sound. It’s not anything to worry about. Ensure that the pivot cup is intact.
Waxing and Lubricating
As we’ve suggested before, Skateboard components may be quieted down by using wax or lubricant. Sometimes it works, but only for a short period. Parts may need to be replaced as a result of worn-out parts.
Cheap lubricant may gather dirt and dust, but you can easily wash it off and start again. Don’t use WD-40; instead, use a silicone-based lubricant.
Eventually, the lubricant or wax will no longer be able to decrease the noise. The most cost-effective way is to light some candles and use them as a lubricant. Most of it may be fixed using paraffin candles, which are easy to get at most supermarkets.
Conclusion
Now that we’ve reached the bottom line, I hope we have answered your question on Why does my Skateboard Squeak? As a result of your comprehension of this article, you learned that this issue could be resolved with a few easy actions.
We strongly advise that you follow the measures outlined in this article before going to a repair or purchasing a new skateboard. Remember to have routine maintenance to prolong your skateboard parts’ life. If you find this article interesting, consider sharing it with your friends.
Hi, I am Charles Harris. I opened this site to write as much as I can about my biggest passion – skateboarding!
I started as a clumsy yet passionate rookie 10 years ago to now a still passionate yet much better skateboarder! But I have to tell you, the whole journey has always been fun and rewarding, indeed not without hardship.